Jump to content

It finally happened

Tmuir
 Share

Recommended Posts

Tmuir Distinguished Member

Tmuir

Posted
Posted

Last night whilst reassembling a Felsa 1560 I fired the Return Bar Spring from the keyless work across the room, 45 minutes of searching failed to find it. I'm now about to spend £5.81 plus £2.88 postage to get another one from Cousins.

It was bound to happen to me sooner or later, just hope it doesn't happen too often. :D

  • Like 4
Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
Posted

Welcome to the Club! Did you try the vacuum approach? - vacuum the carpet then go through the dust bag?

Magnet approach? - trail a magnet on a string over the area?

Or did you fall on your knees, cursing creation? - that sometimes helps! :mad:

  • Like 4
Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
Posted

I recently had a part take flight, and my search for half an hour was fruitless, all the time during the search I had my Optivisor on, slightly raised, it was only then, when I took it off, the missing part presented itself on the top of the brow of the Optivisor :woohoo-jumping-smiley-emoticon:

  • Like 2
Link to comment
Share on other sites
sperki77 WRT Addict

sperki77

Posted
Posted

If you roll a strong flashlight slowly across the floor, sometimes the part will make a shadow and appear larger.  I have found missing parts like that.  A magnet is also a life-saver.  Sometimes I sweep the dust on the floor into a dustpan and run the magnet over the dustpan.  Most of the time, though, I'm on my knees either cursing or praying (both techniques work equally as well).  Seems my cursing sometimes makes the part mad enough to appear, and if that doesn't work, the praying may buy me a little mercy and the part, feeling sorry for having treating me so harshly, will come crawling back.  

Whatever your part or whatever your technique, know that you are not alone and all your forum peers are right behind you, cheering you on (with little or no snickering).  :D

Shirley

  • Like 2
Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
  • Author
Posted
9 hours ago, sperki77 said:

If you roll a strong flashlight slowly across the floor, sometimes the part will make a shadow and appear larger.  I have found missing parts like that. 

Shirley

I tried that approach but it did not work this time.

On previous occasions I've always heard a 'tink' to give me an idea where it landed, but this time I heard nothing.

I searched, got my wife to search and tried again the next day before I gave up and ordered the part.

I'm sure tonight it will just appear back on the bench now that I've ordered a replacement...

Link to comment
Share on other sites
canthus Super WRT Addict

canthus

Posted
Posted

Been there many times unfortunately !!!!   :pulling-hair-out:

Non-magnetic parts are the worst !!  I use a large loop of Gaffa Tape (which is very sticky) and inspect whats stuck to it with an eyeglass.  I have found end jewels, inca springs and even long lost bits using this method.  If I have to resort to a vacuum, I cover pipe with a fine cloth (old hanker-chief !) in which I wrap a very strong magnet. 

  • Like 1
Link to comment
Share on other sites
sperki77 WRT Addict

sperki77

Posted
Posted
7 hours ago, Tmuir said:

I tried that approach but it did not work this time.

On previous occasions I've always heard a 'tink' to give me an idea where it landed, but this time I heard nothing.

I searched, got my wife to search and tried again the next day before I gave up and ordered the part.

I'm sure tonight it will just appear back on the bench now that I've ordered a replacement...

Yep!  The quickest way to find a part is to order a replacement...  :D

Link to comment
Share on other sites
sperki77 WRT Addict

sperki77

Posted
Posted
5 hours ago, canthus said:

Been there many times unfortunately !!!!   :pulling-hair-out:

Non-magnetic parts are the worst !!  I use a large loop of Gaffa Tape (which is very sticky) and inspect whats stuck to it with an eyeglass.  I have found end jewels, inca springs and even long lost bits using this method.  If I have to resort to a vacuum, I cover pipe with a fine cloth (old hanker-chief !) in which I wrap a very strong magnet. 

Cool method!  Come to think of it... don't watchmakers have the cleanest floors in town (at least around their workbench)?  :biggrin:

Link to comment
Share on other sites
Folkvisor Super WRT Addict

Folkvisor

Posted
Posted

Using a magnet I've found Novodiac springs in my shirt pocket, my glasses case - when it is in my shirt pocket, on shelves near my work bench and in my hair. I've never found one on the floor; however, I've found other things on the floor.

Once a newly-oiled end jewel ended up on my loop. I was wondering why things had a reddish tinge...

O yes, and after you buy the part you lost you'll almost always find it...

Dave

Link to comment
Share on other sites
Sleeper Member

Sleeper

Posted
Posted

There are nice UV light LED flashlights.  The "Black Light" makes lots of stuff light up like jewels and the blue steel springs.  Handy to have around. 

Also those dandy UK made Dyson Vacuums don't run you parts though the impeller before the make it to the dust bin.   

  • Like 1
Link to comment
Share on other sites
ro63rto Distinguished Member

ro63rto

Posted
Posted
Yup. Good thing I took a closer look.





Also those dandy UK made Dyson Vacuums don't run you parts though the impeller before the make it to the dust bin.   


Any old vacuum cleaner with a piece of the Mrs old tights over the nozzle works perfectly [emoji106]

Sent from my Honor 5c

Link to comment
Share on other sites
  • 1 month later...
Folkvisor Super WRT Addict

Folkvisor

Posted
Posted
On March 16, 2017 at 1:41 PM, StuartBaker104 said:

Fired a strap pin into my printer the other week. Fortunately turning it upside down and shaking for a bit got it out. Was worried for a whike that I was going to have to learn how to take apart something bigger...

To quote Frank Lloyd Wright - rather loosely, "Move your bench."

LOL

Link to comment
Share on other sites
ro63rto Distinguished Member

ro63rto

Posted
Posted
Fired a strap pin into my printer the other week. Fortunately turning it upside down and shaking for a bit got it out. Was worried for a whike that I was going to have to learn how to take apart something bigger...


Just wait until you fire one into your eyeball. Yes, it hurts like hell, now I wear my clear cycling glasses while doing the "big" dismantling stuff.
Will be buying a visor soon so will still be protected [emoji4]

Sent from my Honor 5c

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Waggy
      Pocket watch escape wh

      By Waggy · Posted

      This is a very valid point and a subtlety that I was unaware of until fairly recently, learning all the time, the video below explains this point well:  
    • HectorLooi
      Blew it with a coil

      By HectorLooi · Posted

      You don't have to use his special tester. Any good multimeter would work.
    • nevenbekriev
      Pocket watch escape wh

      By nevenbekriev · Posted

      Yes, it looks like GT Revue 30. Doctor, You can not replace escape wheel by the dimensions You listed. One needs to know much more things like number of leaves of the pinion and it's diameter, the position in high of the table and the pinion, the hight between the pivots, the exact pivots diameter... And then, even if suitable wheel is found, one will need to know how to adjust the pallets position correctly. Restoring antique movements is something different than replacing parts. In older movements parts are not interchangeable, this means spare parts do not exist. Here the case is different, but still escapement adjustment will be needed if a wheel from a donor is found. So may be it will be easier to restore the donor for You...Restoring antique movements usually means making of the parts needed and this requires knowlage and working on lathes skill. In this case repivoting of the wheel is the natural solution, but there is a long way that one must walk untill getting ready for such work.
    • Waggy
      How to store one dip

      By Waggy · Posted

      I was looking at Essence of Renata, a chemical used a lot for cleaning hairsprings: "Specially prepared solution for degreasing watch and instrument components. Indispensable for degreasing hairsprings." Looking at the MSDS you can see this is just pure n-Heptane, so could be an option for those who don't want to use the chlorocarbons or hexane?     HF6013 - Horological Essence COSHH Safety Data Sheet Horological Essence_0.pdf
    • Kkramme
      Self introduction

      By Kkramme · Posted

      Great!! 👍 
×
×
  • Create New...