Jump to content

Spots on old watch


jdrichard

Recommended Posts

Take care with the denture cleaner. It is certainly worth a try on enamel dials provided they don't have any lume paint (or indeed any other decoration painted on top of the enamel) but don't try it with painted, printed, or lacquered dials like the one that @jdrichard has; that way lies potential disaster as the inks and lacquers use are likely to vanish.

  • Like 2
Link to comment
Share on other sites

As already stated the method of using denture cleaners is only good for enamel dials and even then extreme caution has to be used, if you tried it on the dial you have jdrichard I fear you may end up with a nice shiny blank disc. I've said before old watch should look old and oxidisation on the dial is better than having a ruined dial. The picture of the dial you have shown looks perfectly exceptable to me leave it and enjoy you cant easly undo any damage you do by trying to clean it, I would as a collector look upon a watch of that period that had a mint nice shiny new looking dial with suspicion.

  • Like 1
Link to comment
Share on other sites

It's difficult to give a definitive answer because not all dials are made of the same materials. If attempting to clean always try in a not viewing area of the dial if possible. However if it was me I would leave alone as it is showing its a nice vintage watch. 

  • Like 3
Link to comment
Share on other sites

Below is a quick experiment with a denture cleaning tablet (I would like to point out I do have a full set of teeth the tablets where bought to clean white enamel dials which they are very good if used with caution)

This is a old dial from a scrap ladies movement and is typical of the 30's 40's period and is a two tone dial with printed details it is suffering from typical ageing and oxidisation I do wear watches daily that have dials in this condition

DSC_1097_zps79ipyeqk.jpg

As you can see the dial is readable and all the printing can be seen it does however look what can only be described as grimy, so to see if denture cleaners can be used on dials like this to improve the look I soaked the dial for 10 minutes in a solution made from a denture cleaning tablet and deionised water.

DSC_1098_zpsdjgenvro.jpg

Forgiving the fact the photo is not very good the damage done can be seen with the loss of much of the printed fine detail on the dial it has taken only 10 minutes to totally ruin the dial with no improvement in the look of the dial what so ever, it does however smell minty fresh

  • Like 3
Link to comment
Share on other sites

I agree with everyone else, I would leave it as-is if it were me.

@wls1971 ouch!!!! 

@jdrichard If you find out that the lacquer is the cause of the stains, I've had good luck with ammonia based window cleaner (windex), gently rubbed on the face of the dial with a q-tip. However, if you were to try that, be very very gentle, go slow, and rinse the dial really well when you're done.

Link to comment
Share on other sites

Take care with the denture cleaner. It is certainly worth a try on enamel dials provided they don't have any lume paint (or indeed any other decoration painted on top of the enamel) but don't try it with painted, printed, or lacquered dials like the one that [mention=1704]jdrichard[/mention] has; that way lies potential disaster as the inks and lacquers use are likely to vanish.

I used the denture method on an old Illinois PW and lost all the numbers on the second subdial, plus my father in law was out a pack of cleaners. I don't trust this technique a bit and agree with mark

Sent from my GT-N5110 using Tapatalk

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • in general this shouldn't be any change. but in general questions like this it be nice to know the specifics of the watch in other words how was it performing before it was cased up and what is it doing now.
    • just as a reminder this watch is a Swatch group product. This will bring up a problem like spare parts and technical information. that I found some links to some information on when I talk about your watch and some of the technical and basically your watch is equivalent to 2834-2 for which I'm attaching the technical sheets. But equivalent does not mean exactly the same you want to do a search on the group for C07 as we discussed this watch before including the technical differences how it's supposed to be regulated and basically because it's watch group there is no parts availability. https://calibercorner.com/eta-caliber-c07-xxx/   https://www.chrono24.com/magazine/eta-movements-from-the-2824-2-to-the-powermatic-80-p_80840/ https://www.watchuseek.com/threads/h-10-movement-details.4636991/ eta CT_2834-2_FDE_481857_15.pdf
    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
×
×
  • Create New...