Jump to content

G'day from Australia

SteveT

By SteveT
in Introduce Yourself Here

 Share

Recommended Posts

SteveT Watch Enthusiast

SteveT

Posted
Posted

Hi guys,

I'm Steve from Australia. I'm a complete n00b at this hobby but after stumbling across a few youtube videos, I found my way here. This looks like too much fun, to not have a go at my self. I have never pulled apart a watch movement before - the extent of my tinkering is putting the hands back on a watch that was dropped. I have always replaced my own watch batteries*, ever since I have ever owned a watch in my teenage years, I'm now 41. My back ground is in Electronics Engineering, I've been doing it since I joined the Navy at the age of 16, so I'm no stranger to pulling stuff apart, and soldering surface mount components. Although watch repair would be more fiddly I would imagine.

So I guess my first question is, what project do I get my feet wet with?

1.  a working pocket watch movement 

2. try and fix a dead pocket watch 

3. quartz watch working or not, is that easier than a mechanical?

4. just a watch movement 

5. dive right in and have a go at a simple mechanical (no date / calendar) 

Looking on ebay it seams that even a dead watch is more expensive than a brand new cheap chinese mechanical watch (as low as $AUD 2, free shipping) .. It gives a whole new level to the old saying "As mad as a two bob watch!"

 

* by batteries I really mean cells. By definition a battery is a collection of "voltaic cells" (joined together in a single case). The coin cells in a watch are single cells.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Hello Steve, start with a pocket watch as they are very much like a basic mechanical watch, just practice taking it apart and putting it all back, get to know the names of the parts, this will help you in using your tweezers, screwdrivers and your eyeglass. Leave fusee P/W as they are very different. You can find loads of advice on here about starting up including books.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is. I've attached a lesson regarding mainsprings, focussing on the size and strength of the spring within the barrel, you might find helpful. Unfortunately it is a PDF converted from a PowerPoint presentation, but only a slide was lost that was originally a video of fitting a mainspring   Lesson 5 The mainspring.pdf
×
×
  • Create New...