Jump to content

Disassembling a capped jewel


alexndr

Recommended Posts

Hi guys and girls!

I have recently dug into a AS1730- movement. While putting the automatic winding assembly together I noticed that the bridge had two capped jewel holes. Looking at them through a microscope (pictures attached) one can clearly see that there are some fluid residing between the jewels and the caps. Probably fluid left from the cleaning? 

Now I need to know how to pop the assembly open to remove this fluid. Maybe I can push the entire assembly out with the staking tool or something, hoping for it to come apart? 

PICT0028.thumb.JPG.79f28d8af83b6f79a70f0efbec337469.JPG

PICT0029.thumb.JPG.7d7c9a74c8c98db03d2249422f67a410.JPG 

PICT0030.thumb.JPG.a522c92cf066e4e7916ed376b5a61356.JPG

 

PICT0035.thumb.JPG.0ff01ce10de25604c09b42a6640d4905.JPG

  • Like 1
Link to comment
Share on other sites

I am not familiar with this jewel setup. From the pictures, it looks like the brass bezel has slots in it. Is it possible that this bezel is threaded into the bridge??? I would not recommend pushing on this unless you are certain as to the construction.

  • Like 1
Link to comment
Share on other sites

Threaded? Hmm, maybe. There are some circular scratches around the bezel that could indicate it has been unscrewed with a screwdriver before? That would however require the bezel to be raised above the jewel (or some special tool to unscrew it). I can try to get a picture from a different angle of it.

  • Like 1
Link to comment
Share on other sites

Never encountered those either, but the slot sure looks like it's meant to be screwed in/out. If you have something like the forked screwdriver for the "H screws" in Hublot watches you could try that, or just inserting the tips of a tweezer and twisting...

s-l1600-5.jpg

  • Like 1
Link to comment
Share on other sites

Thanks for chippin' in guys! 

 

7 hours ago, StuartBaker104 said:

Have you searched on line for a tech sheet for the movement? I had a quick look, but AS1730 came up blank everywhere - are you sure that's right?

Sorry. You're right. It should be AS 1713. To late to edit the original post.

 

8 hours ago, Pip said:

I'll watch with interest, unfortunately I can't contribute. However, thumbs up for the images, they are exceptionally clear! What microscope / camera do you use?

I'm using an LCD USB microscope (https://www.cousinsuk.com/product/benchtop-digital?code=M39115). I had handheld versions of this before but it was not that practical to work with (required USB wiring to a laptop). The LCD screen is not great but it works. It has an SD memory card slot so it's easy to take photos and transfer to your computer. There is a lag between the optics and the screen so it's not possible to replace the loupe with it but for situations like this, it's awesome. 

 

1 hour ago, matabog said:

I'm not sure it's ment to be disassembled. I would use an IPA spray and an air spray (carefully not to blow the  cap jewel away)

That crossed my mind as well. I cleaned it in an Ultrasonic machine and rinsed with IPA. My ways of working for drying the parts has room for improvements since I have nothing more than a dust blower at hand.  I'll try air, or maybe heat, to dry it out. 

  • Like 1
Link to comment
Share on other sites

That fluid has got to go and also it looks like some crud is in there as well. I have not seen this style of chaton but it certainly looks like it is a screw fitting.If it does not undo then maybe a good ultrasonic clean will shift the crud and if successful warm with a hairdryer to make sure all is dry & then lube using a auto oiler.

Link to comment
Share on other sites

19 minutes ago, rogart63 said:

Glue? Looks like somebody has glued the cap jewel? Maybe because they broke the incabloc spring? Just pop it out and replace with a new spring and a new jewel? 

While that's possible, I would proceed carefully. If those are indeed Incabloc Blocs, then you should be able to see where the slots are undercut to retain the lyre spring. Also - gluing would require quite a bit of care in order to prevent glue from entering the oil sump. It would, of course, also remove any shock protection. I would think someone capable of gluing those cap jewels in place would be capable of replacing a missing lyre spring. Not to mention that there are 4 of these settings. Seems unlikely to me, but anything is possible!

Link to comment
Share on other sites

1 hour ago, rogart63 said:

Glue? Looks like somebody has glued the cap jewel? Maybe because they broke the incabloc spring? Just pop it out and replace with a new spring and a new jewel? 

Struck me as well. The movement has definitely been serviced before. Some one has managed to mess up the crown wheel screw (it's left threaded, or at least it has been). Praying to higher instances that the bridge threading is not totally useless and that a new screw will do.  

1 hour ago, sstakoff said:

Alexndr - can you take another photo of the slot at a 45 deg angle???

I'll do it tonight. 

 

 

  • Like 1
Link to comment
Share on other sites

Hard to get good photos but it seems that there are no slots for lyre springs. 

PICT0037.thumb.JPG.2ed8abf984fe20e23fbcb0b43e663157.JPG

PICT0039.thumb.JPG.3ea5f6158073cdaecbade028e838d9aa.JPG

Cap and bezel is in level so if it's a "screw fit" that would require some special tool (like the H- shaped screw driver suggested). I tried to turn it carefully with some dull tweezers but it wouldn't budge. 

Link to comment
Share on other sites

 

1 hour ago, alexndr said:
1 hour ago, Marc said:

Is it possible to see any evidence of threads in the bridge in the cut outs in the chaton?

No, I can't see any but they might still be there. 

I guess that would have been too easy :unsure:

Link to comment
Share on other sites

  • 2 weeks later...

I seem to remember that these were installed from the non-slotted side and the assembly peened over at the slots. When cleaning you just whack the whole thing out. This will damage the sides so you need to re-install so that the slots are in a fresh part of the hole.

If you measure the circumference of the slotted side and the none slotted side can you see a difference in diameter?

Anil

 

Link to comment
Share on other sites



  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • In the meantime whilst awaiting a better plan, please drop me a quick hello on my email. 
    • I looked at it like this, I've built a lot of stuff in my time, building structures and furniture,those are my creations and they will still be here way way after I'm gone. Traditional watchmakers felt the need to pass their knowledge on, ideas that they created . I assume with them as it is with me, leaving their mark on the earth, a way of being remembered. This creation of Mark's has brought thousands of people together to pass their knowledge around,  ideas that will continue to be used for lifetimes. Ideas that should continue to be procured. If for whatever reason the forum ceased to exist, not quite like Ranfft's, that didn't disappear but much less usable. Then that is sad, such a massive loss of communication between good people and a wealth of knowledge lost. There should be something in place for when that happens which could be next week, next year or in 10 years. Might not be a topical subject for a lot of folk or boardering on controversy, i did say i talk about stuff other people dont. But if you dont talk about it and something happens then you've lost it and you ain't gonna fix it .
    • I've remained silent on this thread, and at the risk of upsetting everyone, the thing that worries me the most the the apparent absence of Mark. The moderators do a great job and the members also pitch in, and the site seems to run itself, but it is a concern for the future of this forum when the owner is absent for all intents and purposes. Like many of the comments above I would hate to log in one day and things be closed down as I rely on this site for ideas and knowledge and also cheer me up. maybe the Moderators could reach out to him, assuming he does not read this thread, and express our concerns and let us know the plans going forward? some kind of WRT ark
    • That was the exact reason for me starting this thread watchie. Still we haven't worked out how the regulars are going to hook up if it goes tits up. I honestly think something should be arranged to stay in contact, we all help each other so much. 
    • Yeah ive watched that a few times before,  i couldnt find my old school dividers to scribe it up 😅 Yep thats the guy i bought a roll from . Thanks Nicklesilver that answers that perfectly and more or less what i thought an experiment over time would prove . The jumper arm is quite thick along its length, i left it that way intentionally, i thought the original was probably very thin, i didnt see that it was already missing. Setting isn't particularly stiff as such just positive, i still need to take it out and polish where it mates with the stem release. 
×
×
  • Create New...