Jump to content

Skills and knowledge for watch repair

Hamish
 Share

Recommended Posts

Hamish Member

Hamish

Posted
Posted

I started this hobby some 10 years ago and took it up to see if I could get some skills and knowledge so that I would have something worthwhile to do in retirement and also partially because I avoid the telly and need distraction from a  job that is stressfull at times. I have never had any formal training, but always liked pulling things apart and fixing them. I have restored/repaired many watches and dont charge for this as long as the watch owner promises to wear Grandads or Dads old watch every now and again. Everyone promises to do this and I do like to see folks wearing these old watches and not having them in the back of a drawer somewhere. 

OK so thats where I am coming from and as I see many new to watch repair folks here, I though a thread starter might be what skills you thought necessary for the jobs we do, how you managed to develop these skills and where you got your knowledge. I'll start it off. Some of what we are likley to say will be obvious, but it maybe of help to newer folk.

I think patience and a reasonably steady hand factors would be important. Just figuring out how to use tweezers and screwdrivers does take time, so take apart and put back together as much as you can. You will get lots of satisfaction through getting something to work and keep reasonable time. Look for old movements, say Bulova - available cheap, which are simple manual wind jobs...you will soon pick it up.

A number of devices can assist eyesight these days but if your eyes are good it really makes it easier.  I am not known for my patience, but I think I have improved this somewhat. Taking time to source the parts carefully requires this. Some projects take years to finish. You need to recognise when it is not fun any more and take a break. Don't jump to conclusions about a fault, but think things through as best as you can. Of course knowledge can be gained by things like Marks videos...I still watch these and pick up lots. I also think an open mind to repair techniques is important as well, that is, dont get locked into doing things one way as another method may actually be better with less chance of breaking something. The first skills I learnt were the manual dexterity ones. We all talk about breaking parts of the first movments we work on so develop the fine skills you need through repitition.

I know we all like pictures, so here are a couple of my workshop.

IMG_2144.JPG

IMG_2145.JPG

IMG_2146.JPG

  • Like 4
Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
Posted

Great insight into your hobby, and some great advice for newbies.  I can relate to some of your findings over the years, patience is key, and as you say, a very steady hand, plus suitable eyewear magnification, lighting etc.

Thanks for the photos, I will share some photos of mine once I have completed my remodelling.

@Geo I managed to find a U.S supplier of the Alvin covering who ship direct to me ;) 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      this is something I've never quite understood about the some of the Swiss companies. In 1957 Omega was using 9010 for the keyless parts with epilam. there's been a slow migration towards using heavier lubrication's but still typically oils and epilam to keep them in place. When it seems like 9504 works so much better.  
    • nevenbekriev
      Is this a 'hack' ?

      By nevenbekriev · Posted

      OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • RichardHarris123
      Any tips to correct a sloppy error?

      By RichardHarris123 · Posted

      Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
×
×
  • Create New...